NX-8 Hardware Reset?

Discussion in 'Security Alarms' started by John Adams, Mar 16, 2007.

  1. John Adams

    John Adams Guest

    Does anyon eknow of a way to default a GE NX-8 panel through the panel
    itself? Similar to DSC's method.
     
    John Adams, Mar 16, 2007
    #1
    1. Advertisements

  2. John Adams

    Crash Gordon Guest

    I use a 6 lb sledge to reset DSCs, maybe it will work on GE as well?

    :)



    "John Adams" <> wrote in message
    news:p...
    | Does anyon eknow of a way to default a GE NX-8 panel through the panel
    | itself? Similar to DSC's method.
    |
    |
     
    Crash Gordon, Mar 16, 2007
    #2
    1. Advertisements

  3. John Adams

    Rich Guest

    Page 11 of the manual

    Enter The Program mode, then

    9 1 0 #

    you will here 3 beeps and take 6 seconds




    "Crash Gordon" <> wrote in message
    news:45fa0ff4$0$502$...
    >I use a 6 lb sledge to reset DSCs, maybe it will work on GE as well?
    >
    > :)
    >
    >
    >
    > "John Adams" <> wrote in message
    > news:p...
    > | Does anyon eknow of a way to default a GE NX-8 panel through the panel
    > | itself? Similar to DSC's method.
    > |
    > |
    >
    >
     
    Rich, Mar 16, 2007
    #3
  4. John Adams

    Frank Olson Guest

    Moe Szyslak wrote:
    > Rich wrote:
    >
    >> Page 11 of the manual
    >>
    >> Enter The Program mode, then
    >>
    >> 9 1 0 #
    >>
    >> you will here 3 beeps and take 6 seconds
    >>

    >
    > Most of these questions come from ->users<- that can not access
    > programming in the first place. Worse case they are *burglars* <---


    Heh... Let 'em try...
     
    Frank Olson, Mar 16, 2007
    #4
  5. John Adams

    Rich Guest

    Ok Point well taken, He stills need a manual and it's listed in there.
     
    Rich, Mar 16, 2007
    #5
  6. John Adams

    John Adams Guest

    "Moe Szyslak" <> wrote in message
    news:...
    > Rich wrote:
    >
    >>Page 11 of the manual
    >>
    >>Enter The Program mode, then
    >>
    >>9 1 0 #
    >>
    >>you will here 3 beeps and take 6 seconds
    >>

    >
    > Most of these questions come from ->users<- that can not access
    > programming in the first place. Worse case they are *burglars* <---
    >
    > It does not help our industry when a panel gets circumvented, either
    > with honest intentions - or a potential burglar.
    >
    > It is best to leave posts like this be, unless you know who is asking
    > - then reply by email.
    >
    >
    >
    >


    No, I am not a burglar (of course one would say that). What I was trying to
    learn was if there was a "hard-wire" reset for this panel.

    DSC's 832 can be defaulted by using a jumper wire between one of the zones
    and another
    terminal during power-up.

    If someone would feel better repling by email please do at:



    thanks,
    John A.

    Brewer Technology Solutions
     
    John Adams, Mar 19, 2007
    #6
  7. John Adams

    ABLE_1 Guest

    John,

    As far as I know the simple answer to your question is no. The panel reset
    is done as written by Rich. Besides if you feel that their should be an
    "hardware reset" then you might be better served to ask Caddx Tech Support.
    Although they will tell you the same as I just have since that is what they
    told me over a year ago. May not be what you want to here but that is the
    way it is.

    Les

    >> Rich wrote:
    >>
    >>>Page 11 of the manual
    >>>
    >>>Enter The Program mode, then
    >>>
    >>>9 1 0 #
    >>>
    >>>you will here 3 beeps and take 6 seconds
    >>>

    >>
    >> Most of these questions come from ->users<- that can not access
    >> programming in the first place. Worse case they are *burglars* <---
    >>
    >> It does not help our industry when a panel gets circumvented, either
    >> with honest intentions - or a potential burglar.
    >>
    >> It is best to leave posts like this be, unless you know who is asking
    >> - then reply by email.
    >>
    >>
    >>
    >>

    >
    > No, I am not a burglar (of course one would say that). What I was trying
    > to
    > learn was if there was a "hard-wire" reset for this panel.
    >
    > DSC's 832 can be defaulted by using a jumper wire between one of the zones
    > and another
    > terminal during power-up.
    >
    > If someone would feel better repling by email please do at:
    >
    >
    >
    > thanks,
    > John A.
    >
    > Brewer Technology Solutions
    >
     
    ABLE_1, Mar 19, 2007
    #7
    1. Advertisements

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads
  1. Guest

    Caddx NX-8 Outputs

    Guest, Jul 16, 2003, in forum: Security Alarms
    Replies:
    7
    Views:
    998
    Petem
    Jul 17, 2003
  2. the_tool_man

    Dimensions for Caddx NX-002 and NX-003?

    the_tool_man, Oct 23, 2003, in forum: Security Alarms
    Replies:
    3
    Views:
    845
    the_tool_man
    Oct 24, 2003
  3. Vincent

    Caddx NX-8 + NX-507 Relay board

    Vincent, Dec 29, 2003, in forum: Security Alarms
    Replies:
    6
    Views:
    1,699
    pudding
    Jan 3, 2004
  4. Truman
    Replies:
    5
    Views:
    1,050
  5. Rich

    Cadds NX-8

    Rich, Oct 4, 2004, in forum: Security Alarms
    Replies:
    0
    Views:
    458
  6. Jerry Napoliano

    Caddx NX-8 w/ Ground Fault

    Jerry Napoliano, Nov 1, 2004, in forum: Security Alarms
    Replies:
    3
    Views:
    1,176
    Nick Markowitz
    Nov 2, 2004
  7. Bruce

    How to reset service light on CADDX NX-6?

    Bruce, Sep 23, 2005, in forum: Security Alarms
    Replies:
    11
    Views:
    7,532
  8. Tim
    Replies:
    1
    Views:
    2,155
    jmk128611
    May 29, 2010
Loading...