Maker Pro
Maker Pro

GE oven failure

R

RonD

Jan 1, 1970
0
I have an old GE range. Model # J BP26 0w2A. It came with the hous
when I bought it 16 years ago. Last year I replaced the bottom heatin
element. This saturday I replaced the broiler element. After that th
oven doesn't heat at all. I suspect it is the temperature control.
The question I have is that there are two tubes. A thick one that is
along the left side of the oven and a thin metal tube along the back,
right against where the broiler element enters the back wall. Bot
enter the oven from the same baffle. I had to move the thin one t
replace the broiler element. Nothing broke as far as I could see.
Which one is the capillary tube and what is the other one for

Ro
 
S

Sam Goldwasser

Jan 1, 1970
0
RonD said:
I have an old GE range. Model # J BP26 0w2A. It came with the house
when I bought it 16 years ago. Last year I replaced the bottom heating
element. This saturday I replaced the broiler element. After that the
oven doesn't heat at all. I suspect it is the temperature control.
The question I have is that there are two tubes. A thick one that is
along the left side of the oven and a thin metal tube along the back,
right against where the broiler element enters the back wall. Both
enter the oven from the same baffle. I had to move the thin one to
replace the broiler element. Nothing broke as far as I could see.
Which one is the capillary tube and what is the other one for.

Did you check for a fuse inside the range? A burnt out element can
blow a fuse if the element shorts to the cladding.

I doubt you did any damage to the temperature sensors and if one did break,
it would probably register too cold so the oven would always be on.

Just some thoughts.

--- sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
R

R!

Jan 1, 1970
0
I have an old GE range. Model # J BP26 0w2A. It came with the house
when I bought it 16 years ago. Last year I replaced the bottom heating
element. This saturday I replaced the broiler element. After that the
oven doesn't heat at all. I suspect it is the temperature control.
The question I have is that there are two tubes. A thick one that is
along the left side of the oven and a thin metal tube along the back,
right against where the broiler element enters the back wall. Both
enter the oven from the same baffle. I had to move the thin one to
replace the broiler element. Nothing broke as far as I could see.
Which one is the capillary tube and what is the other one for.

Ron

If it's a self cleaning oven the thin one is a NAK switch the heavy one
that stick's out of the back of the oven is the temperature sensor.

If standard oven the thin one goes to the thermostat, I had some trouble
with the selector switch.

Former appliance repairman.

R!
 
R

RonD

Jan 1, 1970
0
Sam said:
RonD [email protected] writes:
-
I have an old GE range. Model # J BP26 0w2A. It came with the house
when I bought it 16 years ago. Last year I replaced the botto
heating
element. This saturday I replaced the broiler element. After tha
the
oven doesn't heat at all. I suspect it is the temperature control.
The question I have is that there are two tubes. A thick one that i

along the left side of the oven and a thin metal tube along the back

right against where the broiler element enters the back wall. Both
enter the oven from the same baffle. I had to move the thin one to
replace the broiler element. Nothing broke as far as I could see.
Which one is the capillary tube and what is the other one for.-

Did you check for a fuse inside the range? A burnt out element can
blow a fuse if the element shorts to the cladding.

I doubt you did any damage to the temperature sensors and if one di
break,
it would probably register too cold so the oven would always be on.

Just some thoughts.

--- sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message heade
above is
ignored unless my full name AND either lasers or electronics i
included in the
subject line. Or, you can contact me via the Feedback Form in th
FAQs.


Sam

Thanks for your reply. The bottom element was working before
replaced the top broiler element. All the top burners and all th
indicator ligts are working, including the "oven on" indicator.
However the fuse check is a good idea. However I have a more immediat
plumbing problem that just cropped up. So I am heading to the plumbin
section, as I can't fix this one either.

Ro
 
H

Homer J Simpson

Jan 1, 1970
0
Thanks for your reply. The bottom element was working before I
replaced the top broiler element. All the top burners and all the
indicator ligts are working, including the "oven on" indicator.
However the fuse check is a good idea. However I have a more immediate
plumbing problem that just cropped up. So I am heading to the plumbing
section, as I can't fix this one either.

The Money Pit (1986). Starring: Tom Hanks, Shelley Long Director: Richard
Benjamin
 
Top