Connect with us

Trying to find an appropriate socket for an IC

Reply to Thread

Discussion in 'General Electronics Discussion' started by Inglorious89, Jan 27, 2015.

Scroll to continue with content
  1. Jan 27, 2015 #1
    Inglorious89

    Inglorious89

    11
    0
    Jan 27, 2015
    I'm trying to find a socket for an BU94601KV-ZAE2. Currently all I can find are these two sockets: http://www.mouser.com/ds/2/448/s_ic149_64p-12789.pdf and http://www.elnec.com/products/programming-adapters/?f=DIL40_VQFP64_ZIF_AWM-1. Would either of these work? And if neither works, then is there a socket that will work?

    The datasheet for the IC is here: http://rohmfs.rohm.com/en/products/databook/datasheet/ic/audio_video/audio_processor/bu94601kv-e.pdf and the store page of the socket from Mouser is here:http://www.mouser.com/ProductDetail...IC149-064-075-B5/?qs=nO3wRANIIvmk4SuYw7mG2g==
     
    Last edited: Jan 27, 2015
  2. Jan 27, 2015 #2
    davenn

    davenn Moderator

    13,883
    1,966
    Sep 5, 2009
    hi there

    that particular version you have shown is NOT DESIGNED for a socket it is for surface mount only
    there may be a socketable version, I don't know ??

    The datasheet for that IC only shows a solder type
     
  3. Jan 27, 2015 #3
    shrtrnd

    shrtrnd

    3,826
    520
    Jan 15, 2010
    Good luck finding what you want. I've been having a lot of problems finding sockets too. Manufacturers are turning-out most surface moount devices now, and the companies that made sockets :)Mill-Max, Aries, Samtec, the guys I
    used to buy from), have really cut back on what they offer now. I've resorted to finding obsolete component vendors, looking for specific sizes of sockets that USED to be made, but aren't any more.
     
  4. Jan 27, 2015 #4
    BobK

    BobK

    7,682
    1,688
    Jan 5, 2010
    Actually it looks like the socket from Mouser does fit the chip. But did you notice the price?

    Edit: Also, how do you expect the socket to help you? If you think you can avoid difficult soldering, the socket is going to be more difficult to solder than the chip.

    Bob
     
    Last edited: Jan 27, 2015
  5. Jan 27, 2015 #5
    davenn

    davenn Moderator

    13,883
    1,966
    Sep 5, 2009
    Bob
    I think you will find those sockets are for these style IC's where the pins cure under the chip and the chip pushes snuggly into the socket

    th6TGO1MN2.jpg

    and not the style of SMD chip in the OP where the pins are orientated outwards as in the OP

    cheers
    Dave
     
  6. Jan 28, 2015 #6
    BobK

    BobK

    7,682
    1,688
    Jan 5, 2010
    Dave,

    Click the last link. It shows a typical TQFP chip with the leads splaying out. The dimensions are exactly the same as the chip OP wants to use. And for $93 I don't think it is intended for chips that need a socket. It is a socket for chips that are normally soldered.

    Bob
     
    davenn likes this.
  7. Jan 28, 2015 #7
    KJ6EAD

    KJ6EAD

    1,114
    159
    Aug 13, 2011
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. Trying to identify an SMD

  2. Trying to identify an SMD

  3. Appropriate driver for an IGBT 600 V

  4. Trying to understand an ac principle.

  5. Trying to match an old terminal block

  6. Trying to find capacitors for tube amp

  7. Bought an amplifier, trying to disprove the company

  8. Trying to find a device!

Loading...
Electronics Point Logo
Continue to site
Quote of the day

“”

-