Connect with us

Sick of my breadboard! quality breadboard recommendations please.

Discussion in 'General Electronics Discussion' started by Robert Hill, Nov 13, 2017.

Scroll to continue with content
  1. Robert Hill

    Robert Hill

    111
    12
    Mar 5, 2015
    GRRRRRRR!

    I'm so fed up with my rubbish breadboard. I never know whether there is an issue with my circuit or arduino code or components or wires but usually its the connections in the breadboard that are at fault. I've just spent ages trying to get some RF transmitters to work and eventually how did I do it? wiggling the arduino around in the breadboard holes a bit!

    Anyway, rant aside (maybe it will help some other frustrated electronics dabblers not to feel alone with their annoyance?)

    Could anyone recommend a good quality breadboard from a good supplier (unless a good one can be got from ebay?) I want to put it on my Christmas list and free my self from the evil breadboard I have currently.

    recommendations greatfully received.
     
  2. kellys_eye

    kellys_eye

    4,279
    1,146
    Jun 25, 2010
    Get one from Rapid or Farnell.

    If it [email protected] out on you then get a replacement under warranty.
     
  3. BobK

    BobK

    7,671
    1,681
    Jan 5, 2010
    Breadboards have too much stray capacitance for RF work. Use stripboard, and keep everything compact.

    Bob
     
  4. davenn

    davenn Moderator

    13,435
    1,807
    Sep 5, 2009
    As BobK said they are not good for RF
    DO NOT use breadboards for RF work

    did I make that clear enough ? :)


    Dave
     
    darren adcock likes this.
  5. Cannonball

    Cannonball

    177
    48
    May 6, 2017
    Robert

    I am sorry that you are having trouble with your breadboard. I have several of them and I LUV them. I also have had that problem, but I do what you did to make them work. I am careful when I am building a circuit. I make sure the wire ends are clean. If they are dull I scrape them clean and when I plug them into the circuit connections I make sure that they are completely in.

    I have built a colpitts oscillator that operates in vhf frequencies. When you get up to rf frequencies you do have to be more careful about wire lengths and good connections. Have fun!
     
    jilfe likes this.
  6. Audioguru

    Audioguru

    2,693
    609
    Sep 24, 2016
    I gave up using a solderless breadboard 42 years ago and have used a compact and soldered stripboard ever since.
    Most of my many projects at work were custom and only one prototype was made and sold as the finished item.
    They looked like a pcb. Here is my FM transmitter:
     

    Attached Files:

    darren adcock and Cannonball like this.
  7. Harald Kapp

    Harald Kapp Moderator Moderator

    9,544
    1,970
    Nov 17, 2011
    Nice and tidy work :)
     
    darren adcock likes this.
  8. kellys_eye

    kellys_eye

    4,279
    1,146
    Jun 25, 2010
    I've seen stripboard that has the exact same copper strip layout as standard breadboard designed for those who wish to simply 'copy over' their stripboard layout to a more permanent form (soldered).

    More recently I've taken to using coper plane perfboard - individual component lands on one side, solid copper plane on the other. This allows for extremely high density project layouts if you use the top plane as a ground (most connections on designs are ground anyway) and a small hand held drill bit to make clearance for leads that aren't grounded.

    Here's a pic of a NE612-based receiver with crystal filter, BFO, AGC and audio amp built onto a board measuring 3" x 2" (incomplete at that stage) to show how dense they can be made.

    ATS-3B.jpg
     
    Last edited: Nov 15, 2017
    Cannonball likes this.
  9. Robert Hill

    Robert Hill

    111
    12
    Mar 5, 2015
    Thanks for the replies.

    Did you guys just go straight to stripboard as the prototype/design/mock up and not use breadboards at all?

    I guess i'm not quite good enough to get things right first time, but as you all suggest with RF the breadboard causes issues so i'll ditch it in this case and get soldering.
     
  10. kellys_eye

    kellys_eye

    4,279
    1,146
    Jun 25, 2010
    I'd rather use Manhattan construction than a protoboard!

    For RF work I use copper clad board with small 'lands' (I make mine by punching out mini circles using a hole punch and 0.2mm copper clad material then glueing the 'dots' around where needed).

    Sometimes I can't even bother transferring the prototypes to 'real' pcbs and just box them up!
     
  11. BobK

    BobK

    7,671
    1,681
    Jan 5, 2010
    The big problem with breadboards and RF is that, even if you do get the circuit working, you cannot transfer it as is to a permanent build using stripboard or pcboard because the capacitance will not be the same.

    Bob
     
  12. Cannonball

    Cannonball

    177
    48
    May 6, 2017
    Don't give up on breadboards yet. They still work on most circuits.

    Besides it is easier to correct a mistake on a breadboard than if it is soldered into a circuit board.

    Stick with it. It will pay off especially while you are learning.
     
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Electronics Point Logo
Continue to site
Quote of the day

-