Connect with us

questions regarding Paradox Alarm

Discussion in 'Security Alarms' started by Alboon, Aug 22, 2011.

Scroll to continue with content
  1. Alboon

    Alboon Guest

    Hello,

    I just bought a house with an alarm. But the setup did not suit me so I
    decided to modify its operation (number of zones, time etc ...). This is
    what I have:
    - 5 "476+" Paradox sensors
    - 2 keyboards MG10LEDV
    - A bell Altec Sirus (v1)
    - The alarm system "Paradox SP6000"
    - a telephone transmitter : Altec Simpl'Vox (v2)

    I have several questions:

    - I did a reset of the system so that I could define areas but I
    understand that a reset changes the intensity of battery charging
    (350mA default): I do not have a special installation, but do you think
    for some reason I need to specify 700mA instead of 350mA?
    - Apparently the SP6000 has an integrated telephone dialer: so what is
    the utility to add this Altec transmitter ?
    - Finally, is it possible to test the alarm to sound without the bell?
    In fact, I put 30s delay for "night mode" but the bell sounded at the
    end of 3-4s, I can not explain why. And I'd like to push my tests a
    little further without waking the neighbors up.

    Thank you in advance for your answers.
     
  2. Alboon

    Alboon Guest

    Le 01/09/2011 21:37, tourman a écrit :
    I think that Altec transmitter allows to transmit data AND vocal
    messages, apparently the SP6000 only sends data messages (not sure...).
    For example, I theorically can hear the inside of my house, even if I'm
    away, by dialing my home number. I can talk and my voice will be heard
    by the thief, thanxs to the transmitter. So I think this Altec thing has
    a few features more than the SP6000 actually has...
    I disconnected the bell which is inside the house, just by unplugging a
    wire, very easy). But the one outside is situated quite high on the roof
    so I can't easily reach it. I tried to disconnect one wire leading to
    the outside bell on the SP6000 but of course it triggered the bell :)
    In fact, I must add that the time when the bell rang after 3s, I
    discovered the same morning that I had a plug, in which my TV was
    plugged, which didn't work anymore. The wires behind the plug are still
    attached to it so my guess is that something went wrong in my
    "electrical bay" (sorry I'm not sure this is how you call it in english
    ; I just mean the place in which every wire is connected, behind
    different fuses, except I don't have fuses but a system more modern).
    Maybe it has something to see with my problem, but I haven't checked yet
    the "electrical bay", I'm waiting for someone experienced. And when I
    tested the "night mode" 3 days ago it rang after 45s, as I wanted...

    Moreover, in case you are interested in my configuration, this is what I
    wanted :
    - I have 5 detectors : 3 near windows, 1 in the garage, and 1 in the
    entry of the house.
    - partial mode : only the garage might trigger the alarm
    - night mode : the detectors inside the house allow 30s before
    triggering the alarm, and the detector in the garage allows a little bit
    more, because I want to open the door, park my car, walk and then reach
    the keyboard to put in my code.
    - complete mode : 3 detectors trigger the alarm immediately and 2 (entry
    + garage) allows time to put in the code.


    I set my detectors as follow :
    - 3 detectors (near the windows) as "type zone 09" : I want them to
    trigger the alarm immediately when I put the alarm in "complete mode",
    and after a few seconds (default 15s, set as 30s) when I put it in
    "night mode", and no triggering when in "partial mode".
    - the detector in the garage is set as "type zone 02" : I want to have
    45s (default delay) in each situation
    - the detector in the entry of the house, is "type zone 03" : no alarm
    in partial and night modes (I would have liked it to trigger after a
    delay, in night mode, but I don't think it's compatible with my other
    expectations), but "delay 1" (45s default) in complete mode.

    Thank you so much, again... And sorry I don't think everything is clear
    enough...
     
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Electronics Point Logo
Continue to site
Quote of the day

-