Connect with us

New Soldering Station? XYTronics LF855-D

Reply to Thread

Discussion in 'Troubleshooting and Repair' started by rudedog9d, Oct 12, 2012.

Scroll to continue with content
  1. Oct 12, 2012 #1
    rudedog9d

    rudedog9d

    1
    0
    Oct 10, 2012
    So I had a Weller Heat a Print, which apparently had support ended for it in the early 90's, so when my tip crapped the bed I figured it was just time to upgrade. I've Looked at some different stuff, and I wondered what some others might think about a LF855-D?I do a wide variety of Electronics repair, usually relatively small stuff. I'm in high school so I only have a few hundred to spend on a new system, and that's also why I don't really have a specialty.

    So, That's my story and what I found. If any one has ever tried one of those, or if you have other suggestions, I'm open to Ideas! Some links to the LF 855-d System Below.

    http://www.xytronic-usa.com/shop/item.aspx?itemid=27
    http://www.jameco.com/1/1/5457-lf-8...ti-function-surface-mount-rework-station.html
    http://www.jameco.com/Jameco/Products/ProdDS/2144577.pdf
    https://www.howardelectronics.com/xytronic/Images/LLF-855D.jpg

    Thanks alot!
    -Brodie
     
    Last edited: Oct 12, 2012
  2. Oct 12, 2012 #2
    CocaCola

    CocaCola

    3,635
    5
    Apr 7, 2012
    No opinion on the one you have linked...

    But, even though you find a lot of 'negative' stigma attached to the China imports on the Internet, I will continue to FIRMLY stand behind them as a damn good $ for $ alternative to the name brands... I have been using them full time for years and have had VERY little to no issues at all, they simply work and continue to work year after year...

    I don't have the exact dates off the top of my head but give or take in the last 12-14 years I have burned out only one heating element in one station, that is the only fault I have had besides your normal tip replacement schedule... The new replacement wand (to lazy to tinker with a heating element swap for the price) for that station cost a whopping $12 to replace and it still functions to this day... And it's not uncommon for me to have the station(s) on for 12+ hours a day...

    If you are one of the guys that has to have Snap-On tools because Stanley isn't 'shinny' enough, the cheap import stations are probably not for you, but if you want a lot of bang for you buck, don't dismiss them...

    The ones I use are the house branded 'CSI' one from Circuit Specialist...

    This regular station...

    http://www.circuitspecialists.com/csi-station1a.html

    And this rework station to be exact...

    http://www.circuitspecialists.com/csi906.html

    If nothing else have a look around their site at what they offer in 'cheaper' alternatives to the big names...

    http://www.circuitspecialists.com/soldering-equipment
     
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. Yihua soldering station review

  2. Weller EC1002 Soldering station repair

  3. Plug on Weller WTCP 50 soldering station?

  4. Weller WS 81 soldering station not working..

  5. Solomon SL-30 Soldering Station won't heat

  6. Help in repair of TS-1564 Soldering Station

  7. Soldering new DC connector on Super Nintendo

  8. I have a Weller W-TCP-L Soldering Station with problems

Loading...
Electronics Point Logo
Continue to site
Quote of the day

“”

-