Connect with us

Need help finding power supply

Discussion in 'Power Electronics' started by gilf0yle, Apr 14, 2018.

  1. gilf0yle

    gilf0yle

    1
    0
    Apr 14, 2018
    Long story short, the transformer on my power supply got damaged and I am in the market for a new one. I really need help finding someone or a company that sells these. Any leads would be immensely appreciated.
     

    Attached Files:

  2. kellys_eye

    kellys_eye

    4,286
    1,143
    Jun 25, 2010
    Insufficient information.

    Output voltage(s)? Output current? Overall wattage? Input voltage?
     
    davenn likes this.
  3. duke37

    duke37

    5,118
    688
    Jan 9, 2011
    What makes you think the transformer is faulty?
    Do the reservoir capacitors have flat tops?

    The transformer runs at high frequency so will have few turns. You may be able to rewind.
     
    davenn likes this.
  4. WHONOES

    WHONOES

    580
    113
    May 20, 2017
    If the transformer has indeed failed, it will be very specific to that particular power supply. If so, the only solution if the manufacturer will not supply a replacement which they probably won't, will be to re-wind it.
    Have you checked to see if the switching transistor is working?
     
  5. dave9

    dave9

    582
    121
    Mar 5, 2017
    You're far more likely to find the entire power board OR the entire product as salvage and pull the power board or just transformer (since the transformer itself is an unlikely failure point) out of it.

    I second duke37's question, what led to the conclusion that the transformer failed, how did it happen?

    If all else fails, you could substitute a different power board with the same voltage and equal or greater current specs, and if it doesn't have the minor (lower current and voltage) power rails then you can take those off the output of the major power rail voltage.

    If it is not required to have the replacement PSU be contained within the original product then it becomes even easier to source a PSU for a tethered-brick arrangement where the replacement PSU is external to the product.
     
  6. ramussons

    ramussons

    337
    61
    Jun 10, 2014
    Long story too short. :D
    To what does the power supply belong to?
    Those transformers very rarely fail. Check that switching transistor / IC mounted on the heat sink between L2 and C43.
     
  7. AnalogKid

    AnalogKid

    2,229
    628
    Jun 10, 2015
    Lambda is one of the largest power supply manufacturers in the world. That transformer is a fully custom design, prototyped and verified in-house and then shopped out to a low cost, high-volume manufacturer for production. Long story short - you cannot buy a replacement transformer.

    As above, the odds that the transformer has failed are very low. Everything on the top side looks OK. Close-up, in-focus photo of the bottom side - ?

    ak
     
  8. timff

    timff

    21
    4
    Apr 13, 2018
    I am not sure if you are asking for a source of a replacement transformer or a replacement power supply. The title of your post would indicate the later.

    The connector strip on the left looks like it is integrated in a larger system. Since Lambda is indicated on the board, they may be able to supply a replacement board. However, they may have made the board for whoever manufactures the larger system in which case a replacement board might have to be ordered from them.
     
  9. AnalogKid

    AnalogKid

    2,229
    628
    Jun 10, 2015
    The two connectors on the left are industry standard 0.156" pin headers with a friction lock/polarizing back. The upper part is a 5 pin part with two pins removed to meet UL creepage distance rules. AMP (Tyco) MTA and MTE series are mating parts, along with others from just about everyone.

    ak
     
  10. bushtech

    bushtech

    847
    132
    Sep 13, 2016
    Op last seen April 14
     
    davenn likes this.
Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Electronics Point Logo
Continue to site
Quote of the day

-