Maker Pro
Maker Pro

Modem

R

Rich

Jan 1, 1970
0
Modem setup on caddx DL900,

In the dialing prefix can I place a *70 D

To bypass my call waiting with a delay?

Or do I have to have in the panel phone number?

Rich
 
M

Mark Leuck

Jan 1, 1970
0
Well that would bypass call waiting to the panel, if you had it in the panel
programming the panel would bypass call waiting

To be honest I never cared about doing it since the panel spends so little
time sending a signal it seems moot
 
J

Jim

Jan 1, 1970
0
Rich said:
Modem setup on caddx DL900,

In the dialing prefix can I place a *70 D

To bypass my call waiting with a delay?

Or do I have to have in the panel phone number?

Rich

I wouldn't recommend doing it in the panel. It's not so much a problem
when you have it, but it does become a problem if they cancel call
waiting. If you dial a *70 and they don't have call waiting the call
wont go out.
 
M

mikey

Jan 1, 1970
0
Jim said:
I wouldn't recommend doing it in the panel. It's not so much a problem
when you have it, but it does become a problem if they cancel call
waiting. If you dial a *70 and they don't have call waiting the call
wont go out.

I've always wondered about that one. I never use it for that very reason but
I've always sort of felt guilty about it. If a call waiting signal did
interrupt a transmission, wouldn't the dialler try again. "course if the
caller kept trying to call too...
It's a wonder I get any sleep at all.
 
R

Rich

Jan 1, 1970
0
Let me retry this, From my home when I call a panal to make a change to a
coustermor equipment. I have call wating and when iam on line with a panal
it gives me erros.

How can I trun it off here. And add delay from the two different dial tones.
 
A

alarman

Jan 1, 1970
0
mikey said:
I've always wondered about that one. I never use it for that very reason but
I've always sort of felt guilty about it. If a call waiting signal did
interrupt a transmission, wouldn't the dialler try again. "course if the
caller kept trying to call too...
It's a wonder I get any sleep at all.

I program the 1st number with the c/w cancel string, and the backup number
without it, and then program the panel to alternate between the two.
js
 
R

Rich

Jan 1, 1970
0
Do I need a delay from the *70 (space) 234-9001

I was going to add in the modem prefix to make it easy.
 
M

mikey

Jan 1, 1970
0
of course dammit, better than not using it at all, good one
 
F

Frank Olson

Jan 1, 1970
0
aware said:
aware had written this in response to
http://www.secure-gear.com/alt.security.alarms/5/Re-Modem-article6864-.htm
:
Hi all,
Tried to post new subject but error 404 came back always...
So my question best fits in this post:
I have a Motorola SM56 Data Fax Modem and when trying to connect with NX8
(using DL900 3.04 winxp), I always get "error writing data to module
0....0". This error appears after the machine has answered successfully.

Is it difficult to please help me with this error? I tried almost all
modems and the special settings at string 2 with no luck yet...

Many thanks,
Al

Is your modem on the software's compatibility list? In most instances
there's a "range" of modems the manufacturer suggests work best with
their products.
 
I have found that I can sometimes get non-listed modem to work by modifying
the register codes but this demand a bit of work
Hi all and thanks for the help,

I tried playing with all settings of the modem but without luck.
Is there any Cheap, USB modem to buy from ebay to connect in the old
and surefire traditional way?

Please advise and help me connect with the NX8 panel,

Alexis
 
Top