Maker Pro
Maker Pro

ICF-2001D Manual Tuning Fault

N

Nick

Jan 1, 1970
0
Greetings!

My cherished ICF-2001D has developed a fault that someone on this
group might have seen before and fixed.

Turning the Manual Tuning CW increments the frequency and display
normally

0.1 kHz LW,MW,SW
50 kHz FM

However turning it ACW does not decrement the frequency and display,
rather it increments it

0.7 kHz LW,MW,SW
350 kHz FM

When holding down the Present Time Set button the Manual Tuning
increments and decrements the clock display directly.

Setting frequency via the keypad works fine.

The clock is driven by IC501 and the radio by IC502, so I think there
maybe something wrong with IC502 or the communication between IC501
and IC502.

The Rotary Encoder and its associated logic IC504, IC505 seem to work
properly.

Also all the pins on IC502 seem to be doing the right things on a
scope, although I don't really have enough servicing detail to tell.

Has anyone seen this fault before?

Does anyone have a spare working keypad/display pcb so I can do a
substitution test?

I am loath to scrap this radio, but I can't imagine that the spares
are easy to come by at this level.

TIA

Nick
 
J

Jerry G.

Jan 1, 1970
0
I cannot remember a lot of details for this receiver. I would look for an
"All Reset" at the rear of the set, or inside. Also, if this model has a
memory battery, many of the Sony's used some "AA" cells, remove these for
about 20 seconds.

If you can prove that the tuning encoder is working properly, the only thing
I can think of is that the IC's that process the tuning may be at fault.

You would really need the service manual for this set, to get in to it.
Maybe Sam's would be able to supply it for you. I would think it is too old
for Sony to have it any longer.

The only other problem I can see with this set, is to have parts. This will
be another issue for you. These Sony sets are very good, but Sony is not
very good for having parts for their older models. This is a big drawback
with this manufacture.

--

Jerry G.
==========================


Greetings!

My cherished ICF-2001D has developed a fault that someone on this
group might have seen before and fixed.

Turning the Manual Tuning CW increments the frequency and display
normally

0.1 kHz LW,MW,SW
50 kHz FM

However turning it ACW does not decrement the frequency and display,
rather it increments it

0.7 kHz LW,MW,SW
350 kHz FM

When holding down the Present Time Set button the Manual Tuning
increments and decrements the clock display directly.

Setting frequency via the keypad works fine.

The clock is driven by IC501 and the radio by IC502, so I think there
maybe something wrong with IC502 or the communication between IC501
and IC502.

The Rotary Encoder and its associated logic IC504, IC505 seem to work
properly.

Also all the pins on IC502 seem to be doing the right things on a
scope, although I don't really have enough servicing detail to tell.

Has anyone seen this fault before?

Does anyone have a spare working keypad/display pcb so I can do a
substitution test?

I am loath to scrap this radio, but I can't imagine that the spares
are easy to come by at this level.

TIA

Nick
 
J

Jock.

Jan 1, 1970
0
I cannot remember a lot of details for this receiver. I would look for an
"All Reset" at the rear of the set, or inside. Also, if this model has a
memory battery, many of the Sony's used some "AA" cells, remove these for
about 20 seconds.

http://www.apostrophe.fsnet.co.uk/

--

|
\_| [] [_ |<

Best viewed in Ebriated.
 
I

Isaac Wingfield

Jan 1, 1970
0
"Nick" <[email protected]> said:
Greetings!

My cherished ICF-2001D has developed a fault that someone on this
group might have seen before and fixed.

Try these numbers for Sony Publications: 1-800-488-7669 or
1- 816-891-7550.

I have't called them for a few years, but it used to be possible to get
manuals from them.

Isaac
 
N

Nick

Jan 1, 1970
0
Thank you Jerry G and Isaac W for your suggestions.

Nick
 
N

Nigel

Jan 1, 1970
0
Nick said:
Greetings!

My cherished ICF-2001D has developed a fault that someone on this
group might have seen before and fixed.

Turning the Manual Tuning CW increments the frequency and display
normally

0.1 kHz LW,MW,SW
50 kHz FM

However turning it ACW does not decrement the frequency and display,
rather it increments it

0.7 kHz LW,MW,SW
350 kHz FM

When holding down the Present Time Set button the Manual Tuning
increments and decrements the clock display directly.

Setting frequency via the keypad works fine.

The clock is driven by IC501 and the radio by IC502, so I think there
maybe something wrong with IC502 or the communication between IC501
and IC502.

The Rotary Encoder and its associated logic IC504, IC505 seem to work
properly.

Also all the pins on IC502 seem to be doing the right things on a
scope, although I don't really have enough servicing detail to tell.

Has anyone seen this fault before?

Does anyone have a spare working keypad/display pcb so I can do a
substitution test?

I am loath to scrap this radio, but I can't imagine that the spares
are easy to come by at this level.

TIA

Nick

The only fault I have listed for this model is 'Lock slips in Sync
dectection mode' - I don't know if that sounds like your problem. If so,
the remedy is to replace R177, R609,R610 and R612.
 
N

Nick

Jan 1, 1970
0
Nigel said:
The only fault I have listed for this model is 'Lock slips in Sync
dectection mode' - I don't know if that sounds like your problem. If so,
the remedy is to replace R177, R609,R610 and R612.

I don't think that is the same thing Nigel.

I think that refers to the synchronous detection used for AM stations.

Having played around with it most of yesterday I think there is a fault
with the microprocessors on the keypad/display board, so unless I can
get a replacement board then it's a goner!

Nick
 
Top