Connect with us

how to send signal wirelessly

Discussion in 'General Electronics Discussion' started by nowayinhell, Mar 1, 2016.

Scroll to continue with content
  1. nowayinhell

    nowayinhell

    2
    0
    Mar 1, 2016
    I have an old Sega mega-drive and I want to make it so the controls are wireless.

    True is I have no idea were to even start to send the signal from the 9 different wires that make up the output wire of the controller and send it wirelessly to a receiver what can do the opposite again and input it into the console.

    Can anyone help me in the right direction?
     
  2. Gryd3

    Gryd3

    4,098
    875
    Jun 25, 2014
    Well... you can look online for a wireless transceiver.
    You will need to build a circuit that reads the controller state and forwards it to a decoder that will mimic a controller.
    There are devices that will mimic the state of a pin on one end to the other, but I don't think they are bi-directional and the added delay may not allow that solution to work...
    It's going to be a fun project, fraught with learning.
     
  3. hevans1944

    hevans1944 Hop - AC8NS

    4,631
    2,159
    Jun 21, 2012
    Fraught might be the right word, but maybe you should look here to see what is already available. Or just order one from here.
     
    Gryd3 and davenn like this.
  4. davenn

    davenn Moderator

    13,903
    1,971
    Sep 5, 2009
    uh huh :) .... no point reinventing the wheel ;)
     
  5. Gryd3

    Gryd3

    4,098
    875
    Jun 25, 2014
    It always seems to be the last step for me... 'Buy a pre-made one for $2'
     
  6. hevans1944

    hevans1944 Hop - AC8NS

    4,631
    2,159
    Jun 21, 2012
    Wheels, no, but mouse traps... ain't electronics grand? I found a Victor electronic trap in my back yard a few days ago with a desiccated dead mouse inside. It had four Sony AA cells inside, mostly all dead too. So I dumped the mouse and took the trap inside my house to see what else was inside (wife not at home at the time... fortunately!).

    Inside the nicely made, injection-molded, plastic box, there was what appeared to be a simple circuit board with a ferrite-core transformer underneath, all secured very nicely with six itty-bitty screws inserted in plastic bosses. Really nice construction, but the elements had done a number on the electrocution electrodes, which were rusted. The real surprise occurred when I turned the circuit board over and looked at its bottom side: several tiny surface-mounted integrated circuits and an assortment of SMD resistors and capacitors were revealed. Besides the on-off slide switch accessible from the outside of the case, there was a tiny pair of contacts inside that the mouse would have brushed against and closed on its way in to the back of the trap, after passing through a simple maze. These might have been the kill switch.

    There was an electrode at the entrance to the maze, and two more inside the kill chamber, but I have no idea what purpose the entrance electrode served. It might have been there to ensure the mouse couldn't somehow turn around and escape without being zapped again on the way out.

    So, all of that for less than twenty-five bucks at Wally World, compared to Victor's old-fashioned wood-plus-spring trap for two bucks, also at Wally World. I guess, for some folks, the extra cost is worth it to not have to deal with a dead mouse. My really old-school solution to a rodent problem: get a mouser (cat). Works for me and it will work for you too if you are a cat person. Only down side is my cat always ate the mouse and brought me the head. Or maybe that was an up side.:D
     
    davenn likes this.
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Electronics Point Logo
Continue to site
Quote of the day

-