Connect with us

Component Identification

Some useful component identification information

Thread Status:
Not open for further replies.
  1. Arouse1973

    Arouse1973 Adam

    5,164
    1,078
    Dec 18, 2013
    Arouse1973 submitted a new resource:

    Component Identification (WIP) - Some useful component identification information

    Read more about this resource...
     
    hevans1944 and Tha fios agaibh like this.
  2. (*steve*)

    (*steve*) ¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd Moderator

    25,214
    2,695
    Jan 21, 2010
    It might be useful to add inductor colour codes too.
     
  3. Arouse1973

    Arouse1973 Adam

    5,164
    1,078
    Dec 18, 2013
    I did, it's under inductor colour codes, or did you want something specific or mean something different?
     
  4. (*steve*)

    (*steve*) ¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd Moderator

    25,214
    2,695
    Jan 21, 2010
    you're right, I must have scrolled right past it.
     
  5. Supercap2F

    Supercap2F

    550
    149
    Mar 22, 2014
    Hey Adam, looks really cool!

    Do you think you could add the manufactures logos that they stamp on ICs? I know only a few, and I have found the right part more then once by knowing them.

    Thanks
    Dan
     
    Arouse1973 likes this.
  6. Arouse1973

    Arouse1973 Adam

    5,164
    1,078
    Dec 18, 2013
    Hi Dan
    I'll have a look, good idea
    Adam
     
    Supercap2F likes this.
  7. Juan

    Juan

    12
    1
    Apr 26, 2014
    Thank you, your post is very, very useful!
     
    Arouse1973 likes this.
  8. WD2Keith

    WD2Keith

    9
    2
    Mar 1, 2017
    Wow can I use this info.. My hat's off to you for this info.. I also like the idea of manufactures insignia referenced too.
     
    Arouse1973 likes this.
  9. Robert_fay

    Robert_fay

    124
    34
    Jun 15, 2017
  10. FuZZ1L0G1C

    FuZZ1L0G1C

    367
    115
    Mar 25, 2014
    DIP-12H.png Similar to QDIP, the DIP-##H IC package is also 2 sets of DIP, but the 2 grounded heat-sink solder tabs/pins drop straight down rather than curve out in the 'Q' tail.
    The 2.5W stereo audio power amp TA8827PL is a DIP-12H example.
    The 'H' horizontal bar is the common ground (heat-sink) on both rails of DIP and package pins form the "uprights" of the H.
    PS- ground pins/tabs not numbered, so (ACW) 1 2 3 , 4 5 6 , , 7 8 9 , 10 11 12.
     
    Last edited: May 20, 2019
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads
There are no similar threads yet.
Loading...
Thread Status:
Not open for further replies.
Electronics Point Logo
Continue to site
Quote of the day

-