Connect with us

Cold Heat

Discussion in 'Electronic Design' started by Clark, Jan 9, 2006.

Scroll to continue with content
  1. Clark

    Clark Guest

    How many of you have rushed out to get one of the Cold/Heat soldering irons.
    Runs off of 4 AA batteries WOW! allot of energy in those babies, most likely
    good for one soldering job.
     
  2. Pooh Bear

    Pooh Bear Guest

    TROLL
     
  3. Bob

    Bob Guest

    You smell a troll? I was kinda hoping for some responses.

    I've wondered, too, if anybody tried using one of these gizmos. Maybe they'd
    make soldering those pesky little 0201 resistors easier ;-0

    Bob
     
  4. Clark

    Clark Guest

    What in the hell is wrong with Poo shit bear, I was asking a question, ****
    you Pooh shit bear you are the troll.

    ..
     
  5. Pooh Bear

    Pooh Bear Guest

    You're for real ?

    They've been discussed here many times.

    Basically totally useless for real electronics.

    Graham
     
  6. Pooh Bear

    Pooh Bear Guest

    Uh ? See my full answer !

    The reason you were considered to be trolling is that no-one with s.e.d
    credibilty would even mention that crap here. It belonged elsewhere. It's not a
    *design* issue.

    Graham
     
  7. Take it easy on him, please. I think Poo Bear must have been badly
    teased or tickled or beaten on as a kid or something. I am hoping
    that his conversations here, are useful therapy for him. He seems to
    have a good heart, once he trusts you.

    I have enjoyed enough of his posts to overlook his impulse to distrust
    with very little provocation. I'm hoping he gets better.
     
  8. Oops. I copied the misspelling of Pooh Bear's name.
    No offense intended.
     
  9. Pooh Bear

    Pooh Bear Guest

    The " Runs off of 4 AA batteries WOW! allot of energy in those babies " suggested
    to me that this was genuine full-blown troll.

    See my later post. I'm not heartless. Honest !

    Graham
     
  10. Pooh Bear

    Pooh Bear Guest

    I suspect that my bullshit detector is more finely honed than your own !

    Seen that too many times.

    No offence intended.

    Graham
     
  11. I saw it as an attempt at humor via sarcasm.
     
  12. Pooh Bear

    Pooh Bear Guest

    Entirely possible I guess ! ;-)

    Graham
     
  13. Non taken.

    It is the honing process you have evidently endured
    that I have probably been spared.
     
  14. Pooh Bear

    Pooh Bear Guest

    Trust me ! You don't want to be subjected to some of that stuff ! I could
    elaborate at length. Comparisons to Dilbert and the PHB would no doubt come
    into play.

    Graham
     
  15. I believe you, and would be willing to listen to the sad stories.

    But I think you might let some of that go and enjoy yourself more,
    when you are here, among friends.
     
  16. Ken Taylor

    Ken Taylor Guest

    I shudder to think who might be Tigger, or Piglet......

    Ken
     
  17. Robert Scott

    Robert Scott Guest

    The "..allot of energy in those babies, most likely
    good for one soldering job." suggests to me that the OP is considering
    both pros and cons of the tool. "allot of energy" in this context is
    taken as sarcasm, as shown in the "[only] one soldering job" comment.


    -Robert Scott
    Ypsilanti, Michigan
     
  18. Rich Grise

    Rich Grise Guest

    I haver a beard trimmer that uses 3 AAs, and they've lasted a couple of
    years so far, not that I spend all that much time trimming my beard. ;-)

    I've also seen a handheld cordless _real_ soldering iron, from Wahl, that
    had a NiCd. I just wouldn't trust one of those little heatless irons,
    because it's just a resistance soldering unit. In fact, I happened on
    a sort of "how to use it" page, and it suggested using the solder itself
    as the resistance medium. Ew! ;-)

    Cheers!
    Rich

    [0]I've corrected your spelling of 'Pooh'. Hope you don't mind. :)
     
  19. Rich Grise

    Rich Grise Guest

    Yabbut, even so, it sounds like the basis of the humour[SIC] or
    sarcausm[SIC] is that the OP doesn't really expect 4 AAs to have enough
    amp-hours to actually do soldering. I think they would - in another post I
    let on as I've seen a Wahl cordless with one 'C'-sized NiCd, and it did
    real soldering. But I wouldn't trust one of those little "heatless"
    resistance solderers.

    Cheers!
    Rich
     
  20. Is the spot for Eeyore already filled? ;-P

    Cheers!
    Rich
     
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Electronics Point Logo
Continue to site
Quote of the day

-