Connect with us

Class D SMPs Combi

Reply to Thread

Discussion in 'Audio' started by Ike Mhlanga, Apr 6, 2021.

Scroll to continue with content
  1. Apr 6, 2021 #1
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    Hi,
    Can someone kindly help me identify this Class D SMPS Combi amplifier.
    If Possible I need schematics.
    Any information that might help with repairs.
    Unit Blew Power Fuse.
    Amp Alarm OK
    SMP Alarm OK
    DS Alarm Flagged
    Regards

    Ike
     
    Last edited: Apr 6, 2021
  2. Apr 6, 2021 #2
    bertus

    bertus Moderator

    2,435
    955
    Nov 8, 2019
    Hello,

    Do you have more details on the amplifier?
    Wich brand and type?

    Bertus
     
  3. Apr 6, 2021 #3
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    I do not have a brand but I have a jpeg picture of it. But its failing to load. Thank you.
    I must be doing something wrong uploading.
     
  4. Apr 6, 2021 #4
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    Good Afternoon,
    I have taken a picture of it but its failing to up load.
    Maybe I am doing something wrong.
     
  5. Apr 6, 2021 #5
    bertus

    bertus Moderator

    2,435
    955
    Nov 8, 2019
    Hello,

    Resize the picture. The forum will accept pictures of about 300 kB.

    Bertus
     
  6. Apr 6, 2021 #6
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    Ok Thank You Very much.
    Here it is. I hope it is clear on your end
     

    Attached Files:

  7. Apr 6, 2021 #7
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    This is the Class D amp. No details on the board as regards the manufacturer.
    The only thing there is are the following:
    PN30302
    Rev AQ
    RRA2017
    Regards
    Ike
     

    Attached Files:

  8. Apr 12, 2021 #8
    WHONOES

    WHONOES

    1,215
    329
    May 20, 2017
    Got absolutely nothing from a gooooooooogle search.
     
  9. Apr 12, 2021 #9
    dave9

    dave9

    1,170
    314
    Mar 5, 2017
    Even with 300K pic size limit, you could do a lot better than that including other sides of it.

    Is it modularized with the left board just a PSU function and the right, connected by wires, the amp board?

    If so, unplug the amp. Try PSU without amp, and try amp with a different PSU. Ideally a current limiting PSU. Somewhere on the board, for example the amp IC, or capacitor ratings, should be hints about a voltage to try. If nothing else I'd try half the rating of the electrolytic caps in the middle of the board, thinking that looks like a dual rail PSU.

    Among the many suspects, I'd suspect a transistor first.
     
  10. Apr 12, 2021 #10
    bertus

    bertus Moderator

    2,435
    955
    Nov 8, 2019
    Hello,

    As said, the picture is to small to see anything.
    You could take pictures of the following sections:
    Ike SMPS class D sections.jpg
    Make pictures of the top and bottom of the given sections.
    Make them about 300 kB each.

    The red section is the high voltage switching part of the SMPS.
    The orange section is the low voltage part of the SMPS.
    The yellow section is the Class D amplifier.

    As @dave9 said, you could try the Class D amplifier on an external power supply.

    Bertus
     
  11. May 13, 2022 at 10:24 AM #11
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018
    Good Day to you all.
    Sorry I have been offline due to unforeseen factors.
    I will try and magnify the pictures as requested by Mr Bertus.
    Corrections:
    1) The Yellow Section is an ADAU 1701 programmable board with Audio Processing.
    Since This is a Powered Sub, The ADAU incorporates the Cross Over as well. Sending signal to the HF section.
    2) The Orange section is indeed the low voltage part Of the power supply.
    It also includes the Class D Power Amp with two Mirrored Class D amps running in parallel.
    The Amp has Two Mirrored IRS 2092 ICs. Each Driving two IRFB 4615 FETs which are running in parallel with the other Mirror.
    The four IRFB FETs are under the board.
    The IRS 2092 carries all the protection.

    I will post the pictures.
    Regards

    Ike
     
  12. May 13, 2022 at 10:40 AM #12
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018



    Hi Dave,
    No it is not modularised. Amp and Power supply are one unit.
    Input is ADAU 1701. Acts as Preamp as well as Cross Over for HF. On separate board.
    To separate I have to cut Tracks.
    You might be right about transistors. They are IRFB 4615 FETs. four in sets of two running in parallel.
    Driven by two IRS 2092 ICs. each driving one side of the Class D amp. They carry the protection.
    The Grey Inductors and capacitors are the Audio decoders on the output of the Parallel Class D Amps.

    I will post larger pictures.
    I tested the FETs and they are ok.
    The amp emits a kind farting sound. which could be the power SMPS but all voltages from the SMPS are ok.

    Thanx for the input.

    Regards

    Ike
     
  13. May 13, 2022 at 10:42 AM #13
    Ike Mhlanga

    Ike Mhlanga

    14
    3
    Feb 12, 2018


    Hi Bertus,
    Thanx for the input.
    I have posted some comments regarding the amp. Maybe the extra detail will help.

    regards

    ike
     
Ask a Question
Want to reply to this thread or ask your own question?
You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.
Similar Threads

  1. Class D audio amp

  2. Amplifier substitute PAM8403 class D amplifier

  3. TPA3122D2 Class D Amp ticking sound and produces no music

  4. Class AB Power Amplifier Design

  5. Problems while making a simple class A amplifier

  6. Can anyone point me to a wideband Class A?

  7. Why use PFC for audio SMPS?

  8. Cross-Regulation vs Transient Response?...SMPS for Audio

Loading...
Electronics Point Logo
Continue to site
Quote of the day

“”

-