Electrical Isolation

Discussion in 'Transformers' started by Tony R. Kuphaldt, Jun 24, 2010.

  1. Tony R. Kuphaldt

    Tony R. Kuphaldt

    Joined:
    Jun 21, 2010
    Messages:
    394
    Aside from the ability to easily convert between different levels of voltage and current in AC and DC circuits, transformers also provide an extremely useful feature called isolation, which is the ability to couple one circuit to another without the use of direct wire connections. We can demonstrate an application of this effect with another SPICE simulation: this time showing "ground" connections for the two circuits, imposing a high DC voltage between one circuit and ground through the use of an additional voltage source:(Figure below)

    [​IMG]

    Transformer isolates 10 Vac at V1 from 250 VDC at V2.

    Code:
    v1 1 0 ac 10 sin
    rbogus1 1 2 1e-12       
    v2 5 0 dc 250   
    l1 2 0 10000    
    l2 3 5 100      
    k l1 l2 0.999   
    vi1 3 4 ac 0    
    rload 4 5 1k    
    .ac lin 1 60 60 
    .print ac v(2,0) i(v1)  
    .print ac v(3,5) i(vi1) 
    .end    
    
    Code:
    DC voltages referenced to ground (node 0):
    (1)    0.0000    (2)    0.0000    (3)  250.0000    
    (4)  250.0000    (5)  250.0000
    
    AC voltages:
    freq          v(2)        i(v1)       
    6.000E+01     1.000E+01   9.975E-05    Primary winding
    
    freq          v(3,5)      i(vi1)      
    6.000E+01     9.962E-01   9.962E-04    Secondary winding
    
    SPICE shows the 250 volts DC being impressed upon the secondary circuit elements with respect to ground, (Figure above) but as you can see there is no effect on the primary circuit (zero DC voltage) at nodes 1 and 2, and the transformation of AC power from primary to secondary circuits remains the same as before. The impressed voltage in this example is often called a common-mode voltage because it is seen at more than one point in the circuit with reference to the common point of ground. The transformer isolates the common-mode voltage so that it is not impressed upon the primary circuit at all, but rather isolated to the secondary side. For the record, it does not matter that the common-mode voltage is DC, either. It could be AC, even at a different frequency, and the transformer would isolate it from the primary circuit all the same.

    There are applications where electrical isolation is needed between two AC circuit without any transformation of voltage or current levels. In these instances, transformers called isolation transformers having 1:1 transformation ratios are used. A benchtop isolation transformer is shown in Figure below.

    [​IMG]

    Isolation transformer isolates power out from the power line.

    • REVIEW:
    • By being able to transfer power from one circuit to another without the use of interconnecting conductors between the two circuits, transformers provide the useful feature of electrical isolation.
    • Transformers designed to provide electrical isolation without stepping voltage and current either up or down are called isolation transformers.

     
    Tony R. Kuphaldt, Jun 24, 2010
    #1
    1. Advertising

Want to reply to this thread or ask your own question?

It takes just 2 minutes to sign up (and it's free!). Just click the sign up button to choose a username and then you can ask your own questions on the forum.
Similar Threads
  1. Fabian Kohler

    Electrical Isolation of USB Data-lines

    Fabian Kohler, Aug 16, 2006, in forum: Electronic Components
    Replies:
    1
    Views:
    1,375
    Roger Hamlett
    Aug 16, 2006
  2. Alex

    Electrical isolation

    Alex, Oct 8, 2003, in forum: Electronic Design
    Replies:
    1
    Views:
    339
    R.Legg
    Oct 10, 2003
  3. Fabian Kohler

    Electrical Isolation of USB Data-lines

    Fabian Kohler, Aug 16, 2006, in forum: Misc Electronics
    Replies:
    0
    Views:
    274
    Fabian Kohler
    Aug 16, 2006
  4. BIGEYE

    Electrical isolation required for mechanical work?

    BIGEYE, Jan 31, 2004, in forum: Electrical Engineering
    Replies:
    3
    Views:
    432
    BIGEYE
    Jan 31, 2004
  5. Les

    Electrical isolation for A/V

    Les, Jun 1, 2006, in forum: Electrical Engineering
    Replies:
    2
    Views:
    258
    Beachcomber
    Jun 1, 2006
Loading...

Share This Page