NX-8 Hardware Reset?

Does anyon eknow of a way to default a GE NX-8 panel through the panel
itself? Similar to DSC's method.

I use a 6 lb sledge to reset DSCs, maybe it will work on GE as well?

:-)



"John Adams" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed) om...
| Does anyon eknow of a way to default a GE NX-8 panel through the panel
| itself? Similar to DSC's method.
|
|

Page 11 of the manual

Enter The Program mode, then

9 1 0 #

you will here 3 beeps and take 6 seconds




"Crash Gordon" <(E-Mail Removed)> wrote in message
news:45fa0ff4$0$502$(E-Mail Removed)...
>I use a 6 lb sledge to reset DSCs, maybe it will work on GE as well?
>
> :-)
>
>
>
> "John Adams" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed) om...
> | Does anyon eknow of a way to default a GE NX-8 panel through the panel
> | itself? Similar to DSC's method.
> |
> |
>
>

Moe Szyslak wrote:
> Rich wrote:
>
>> Page 11 of the manual
>>
>> Enter The Program mode, then
>>
>> 9 1 0 #
>>
>> you will here 3 beeps and take 6 seconds
>>
>
> Most of these questions come from ->users<- that can not access
> programming in the first place. Worse case they are *burglars* <---

Heh... Let 'em try...

Ok Point well taken, He stills need a manual and it's listed in there.

"Moe Szyslak" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> Rich wrote:
>
>>Page 11 of the manual
>>
>>Enter The Program mode, then
>>
>>9 1 0 #
>>
>>you will here 3 beeps and take 6 seconds
>>
>
> Most of these questions come from ->users<- that can not access
> programming in the first place. Worse case they are *burglars* <---
>
> It does not help our industry when a panel gets circumvented, either
> with honest intentions - or a potential burglar.
>
> It is best to leave posts like this be, unless you know who is asking
> - then reply by email.
>
>
>
>

No, I am not a burglar (of course one would say that). What I was trying to
learn was if there was a "hard-wire" reset for this panel.

DSC's 832 can be defaulted by using a jumper wire between one of the zones
and another
terminal during power-up.

If someone would feel better repling by email please do at:

(E-Mail Removed)

thanks,
John A.

Brewer Technology Solutions

John,

As far as I know the simple answer to your question is no. The panel reset
is done as written by Rich. Besides if you feel that their should be an
"hardware reset" then you might be better served to ask Caddx Tech Support.
Although they will tell you the same as I just have since that is what they
told me over a year ago. May not be what you want to here but that is the
way it is.

Les

>> Rich wrote:
>>
>>>Page 11 of the manual
>>>
>>>Enter The Program mode, then
>>>
>>>9 1 0 #
>>>
>>>you will here 3 beeps and take 6 seconds
>>>
>>
>> Most of these questions come from ->users<- that can not access
>> programming in the first place. Worse case they are *burglars* <---
>>
>> It does not help our industry when a panel gets circumvented, either
>> with honest intentions - or a potential burglar.
>>
>> It is best to leave posts like this be, unless you know who is asking
>> - then reply by email.
>>
>>
>>
>>
>
> No, I am not a burglar (of course one would say that). What I was trying
> to
> learn was if there was a "hard-wire" reset for this panel.
>
> DSC's 832 can be defaulted by using a jumper wire between one of the zones
> and another
> terminal during power-up.
>
> If someone would feel better repling by email please do at:
>
> (E-Mail Removed)
>
> thanks,
> John A.
>
> Brewer Technology Solutions
>